| |
Major Features
- Simultaneous full duplex fibre channel 1.0625 Gb/s transfers
- Supports all fibre channel topologies
- Full fabric support using F_Port and FL_Port connections
- Full support for both FC service Class 2 and 3
- 64-bit PCI data and addressing
- End-to-end parity protection
- Robust suite of software including IP and storage protocols under Windows 2000, Windows NT and NetWare
- GBIC or embedded physical interfaces
The LightPulseTM LP850 Fibre Channel PCI Host Bus Adapters deliver exceptional performance through the use of Emulex’s Dragonfly ASIC, a 266 MIPS onboard processor and high speed buffer memory. The LP850 features a 64-bit PCI interface and provides the richest feature set available.
The LP850 provides high-performance fibre channel
connectivity for entry-level Windows 2000/NT and Novell
NetWare systems. Based on the Emulex LP8000 architecture,
the LP850 provides a unique combination of features,
including switched fabric support using F_Port and FL_Port
connections, full-duplex data transfers,high data integrity
features, support for all fibre channel topologies and support
for service classes 2 and 3.
The LP850 also features sophisticated hardware that provides
superior performance in storage area networks, delivering low
latency and high throughput in switched, arbitrated loop and
clustered environments. The LP850 is available with copper
and short-wave optical GBICs as well as embedded copper
and optic interfaces.
The LightPulseTM LP850 is complemented by a rich suite of software support including storage protocol (SCSI), network protocol (IP) as well as multi-protocol (SCSI & IP) operation, enabling advanced storage area network (SAN) implementations in Windows 2000, Windows NT and NetWare environments. All drivers are also fully compatible with the LP9002, LP9000, LP8000, LP7000E and LP950 (2000/NT and NetWare only) host bus adapters.
|
|
Standards
ANSI Fibre Channel FC-PH
ANSI Fibre Channel FC-AL
ANSI Fibre Channel FC-PLDA
ANSI Fibre Channel FC-FLA
PCI Local Bus Revision 2.2
Fibre channel Class 2, 3
Gigabit Interface Converter (GBIC)
Architecture
Emulex Dragonfly ASIC technology
up to 33 MHz PCI bus master DMA
512 KB FLASH memory
1 MB code RAM
128 KB buffer RAM
Software Environments
Windows 2000 SCSI and IP
Windows NT 4.0 (Alpha & x86) SCSI and IP
NetWare 4.2/5.x SCSI
Hardware Environments
x86 and Alpha
PCI hardware platforms
Copper
| Data Rate: |
1.0625 Gb/s |
| Cable Type: |
Dual Twinax or Quad Axial |
| Connector Type: |
DB9 |
| Distance: |
30 meters (98') |
Optical
| Data Rates: |
1.0625 Gb/s |
| Optics: |
short wave lasers |
| Cable |
50/125 µm multi-mode fiber |
| |
62.5/125 µm multi-mode fiber |
| Connector Type: |
dual SC |
| |
500 meters (1640') 50/125 µm fiber |
| |
175 meters (574') 62.5/125 µm fiber |
|
Physical Dimensions
Short PCI form factor 174.75mm x 106.68mm
(6.88" X 4.2")
Power Requirements
| Volts: |
+5 VDC |
| Power |
10 watts typical |
Environmental Conditions
| Operating Temperature: |
0° to 45° C (32° to 113° F) |
| Storage Temperature: |
-10° to 55° C (14° to 131°F ) |
| Relative Humidity: |
5% to 95% non-condensing |
Agency Approvals
| Class 1 Laser Product per DHHS 21CFR (J) and EN60825 |
| UL Recognized to UL 1950 |
| CUR Recognized to CSA22.2, No. 950 |
| TUV Certified to EN60950 |
| FCC Rules, Part 15, Class B* |
| ICES-003, Class B* |
| EMC Directive 89/336/EEC (CE Mark) |
| - EN55022, Class B* |
| - EN50082-1 |
| Australian EMC Framework (C-Tick Mark) |
| AS/NZS 3548, Class B* |
| VCCI, Class B* |
*Note: LP850-D1 is Class A
Ordering Information
| LP850-D1 | Embedded copper DB9 interface |
| LP850-F1 | Embedded multi-mode optic interface |
| LP850-T1 | Copper DB9 GBIC interface |
| LP850-N1 | Multi-mode optic GBIC interface |
|
|
